• Check if gas is flowing or not
• Check if the preamps are turned on or not
• Check if the fans are turned on or not

• Check if the viewers can move correctly or not
  • Target viewer
  • Q1-FC viewer
  • FPS viewer
  • 0-deg. dump viwer
  • 0-deg. Tami-Q viwer

• Check the image from the console
  • Target viewer
  • Q1-FC viewer
  • FPS viewer
  • 0-deg. dump viwer
  • 0-deg. Tami-Q viwer

• Check if the FCs have a correct connection or not by tester
• Check if the FCs have a correct isolation or not by 1000V insulation tester
  • Q1-FC
  • FC at 0-deg. dump
  • FC at FPS
• Check if the FC is connected to current integrator

• Check if all chambers do not have leak or not
  • The pressure should be less than about 1*10^-2 Pa
• Check if all gate valves are open or not

• Check if target ladder can move correctly or not

• Check if the signals are OK or not by oscilloscope
  • The model of PMTs is H7195. The voltage limit is -2700V.

• Check if all magnets can be excited or not

• Energy calibrations

• The log book should be prepared during beam tuning

• Setup and initialization for each experiment
  http://www.rcnp.osaka-u.ac.jp/Divisions/np1-a/pukiwiki/index.php?Setting%20up%20the%20CAGRA%2BGR%20DAQ
• Check if the daq can run or not by using pulser
• Check if the disk space is enough or not

1. Beam transportation
2. Beam transmission > 90%
   • BS3 - FCs at beam dump
3. Start up GR
   1. Plastic scintillators
      1. ADC raw 1d
      2. TDC raw 1d
      3. Correlation between ADC L & R
      4. GR-GV is open or not? Push button sometimes. Looks OK. Hardware things.
      5. Inside of GR chamber? D1-FC is blocking the beam?
      6. Q1-FC is blocking the beam?
   2. RF signals
      1. Raw data is OK?
      2. Channels assignment are OK?
   3. Blocking stuff?
   4. Installing the alminum plate
   5. VDC wire check by continuum
   6. Plastic scintillators HV optimization
   7. VDC HV optimization
   8. Energy calibration by the C target
      • Check if the nuclide of the primary beam is correct or not
      • Coefficient for MeV/mm
      • By the way, SH5 is a momentum slit
   9. Optimization of beam energy resolution with the Au target (achromatic mode)
      1. macro – resmon?
      2. GXTHC
      3. GXCTH
      4. GTHCTH
      5. GX gate
      6. See the histogram list in GR optics
      7. The goal is 80 keV (FWHM) for proton 295 MeV
      8. Au target has some excited states at low energy. This looks a child of the beam?
   10. Changing the beam line setting takes time longer than 30 minutes (Nebiki-san & Furutaka-san)
       1. 50 minutes on Dec. 5, 2017 by Nebiki-san & Furutaka-san
   11. Optimization of beam energy resolution with the Au target (dispersion matching mode)
       1. This optimization should be done after the tuning for achromatic mode
       2. The goal is 20-30 keV (FWHM) with a target for proton 295 MeV (the best value is 14 keV (FWHM))
       3. The goal is 15 keV (FWHM) without a target for proton faint beam at 295 MeV
       4. Change the GR angle from 8.5 degree to 0 degree
       5. SC FC is down
       6. Faint beam
       7. The beam is centered (0 mm) in GX
       8. Check the resolution (30 keV (FWHM) at GX of 0 mm, 25 keV (FWHM) at GX of -400 mm at E377 and E422 on Dec. 5, 2017)
       9. Y focus by changing the QM10 with Au target
       10. Target Au –> blank

1. Q1-magnet focusing with the sieve slit and the carbon target
2. Q1-magnet defocus with the sieve slit and the carbon target

• Beam transportation
• Transmission check
• HV and threshold tuning of plastics
• HV tuning of VDCs

• If no one (magnet at N0 nor EN?) is using the power of the magnets, we can turn off the main switch of the power.
• We do not have to stop the cooling water.

• 0-deg. DSR+ mode
• 0-deg. (p, p') dump mode
• 0-deg. (alpha, alpha') mode

• 1.5-2 days for a single target and a single angle setting
• 1 week for polarized beam for a single target and a single angle setting

• Changing beam line setting from achromatic mode: 1 - 2 hours
• Dispersion matching tuning : 6 hours
• In total 9 hours or something

• Achromatic mode
  • p 300 MeV : 60-100 keV
  • 12C 1200 MeV : 240 - 400 keV

• VDCs
  • HV (initial values): CATH: -4.55kV, POT: -0.30 kV
  • HV (optimized values): CATH: -4.40kV, POT: -0.35 kV

* The web controller is a set of a server side and client side programs

• If you change the program, we have to restart the web browser in order to erase the cash in the browser

* vmeserver:8080 –> Tomcat server is working

• Account: quser
• Password: please ask me

• Always flow the cooling water on the magnets of GR and LAS
• Keep the GR and LAS chambers vacuum
• isobutane is used also by EN (but GR- and LAS-VDCs are the main users)

• VDC threshold 4 uA –> 20 uA (sometimes 40 uA is used for 0 deg. exp.)